Featured Book

LaTeX Beginners Guide

Supporters and Partners

Sponsored by DANTE e.V.: The German speaking TeX Users Group
TeXnique.fr - questions & r├ęponses sur LaTeX
TeXwelt - Fragen und Antworten zu LaTeX
Pic for expressive LaTeX diagrams PDF Print E-mail
(8 votes, average: 4.00 out of 5)
LaTeX - Graphics, Figures & Tables
Written by Allan Espinosa   
Thursday, 21 June 2012 15:47

In my graduate work, I draw a lot of system diagrams which basically involves drawing a bunch of shapes with arrows. When typesetting my figures, I like using the Pic preprocessor because of its expressiveness. In the following post I will show how to use it.

- A contribution to the LaTeX and Graphics contest -

This article is an updated version of a post from my my personal blog.

Take a look at the code below:

A: circle "A"
line right then down
B: circle with .n at Here
line -> from A.s to B.w

This will generate the following figure:


Below is my workflow when writing Pic diagrams:

  1. Install the Pic preprocessor. Most *nix distributions come with the GNU pic along with the groff-related packages. For a more powerful preprocessor, I recommend J. Aplevich's Dpic. It supports preprocessing to other LaTeX graphics libraries such as PSTricks and TiKz. Here we compile the above code using GNU pic:
    $ cat figure.pic | pic -t > figure.tex
  2. Pic is a preprocessor and compiles any code in between the .PS and .PE. Although in principle you can embed them directly in your LaTeX documents, most people practice placing their Pic figures in a separate file.
  3. Embed the generated LaTeX file in your document. The GNU pic(1) manual recommends embedding your latex in a specific way:
  4. Compile your LaTeX code as you normally would.

My first encounter with Pic was when I was looking for ways to typeset my Electrical Engineering reports during undergrad. That time, I found the Circuit_macros package, also by J. Aplevich. Circuit_macros provides a set of M4 macros to draw circuit components. Using it is the same as working with normal Pic figures but you have to pre-process the figures through m4 first.

$ cat figure.m4pic | m4 -I ./circuit_macros | pic -t > figure.tex
Here is an example figure I made during my undergraduate year:


# Usual defs...

IC: box ht 2*dim wid 3*dim "SA612A"
In: capacitor(left_ at IC.w hlf); rlabel(,0.1~\micro\farad,)
circle rad 0.025 fill 0 with .c at In.end
box invis wid 1.5*dim "From" "Modulator" with .e at last circle .w
move to IC.w "1" then right 0.1

move to IC.nw+(2*qrt,0) "8" then down 0.1
move to IC.nw+(2*qrt,0); line up hlf; circle rad 0.025 fill 0 with .c at Here; "$V_S$" above

move to IC.nw+(4*qrt,0) "7" then down 0.1
move to IC.nw+(4*qrt,0); line up hlf;
Junc1: dot

move to IC.ne-(2*qrt,0) "6" then down 0.1
move to IC.ne-(2*qrt,0); line up hlf;
Junc2: dot

capacitor(from Junc1 to Junc2); llabel(,10~\pico\farad,)
capacitor(from Junc1 up_ 1.5*dim); rlabel(,220~\pico\farad,)
line to (Junc2.x,Here.y)
xtal(from Junc2 up_ 1.5*dim); rlabel(,10~\mega\hertz,)

move to IC.sw+(2*qrt,0) "2" then up 0.1
move to IC.sw+(2*qrt,0); capacitor(down_ dim); rlabel(,0.1~\micro\farad,); ground

move to IC.se-(2*qrt,0) "3" then up 0.1
move to IC.se-(2*qrt,0); line down dim; ground

move to IC.e "4" then left 0.1
move to IC.e; capacitor(right_ dim); rlabel(,0.1~\micro\farad,)
line up hlf; antenna(,,T)


There are a lot of better resources on GNU pic/ Dpic and Circuit_macros than this introductory post:


List item
Name *
Email (For verification & Replies)
ChronoComments by Joomla Professional Solutions
Submit Comment

Latest Forum Posts


Re: Cannot see page numbers
24/11/2015 21:03, Johannes_B

Cannot see page numbers
24/11/2015 20:23, Fredo

Re: Error message
24/11/2015 19:12, thatha

Re: Adding a glossary entry with hyperref
24/11/2015 17:40, Johannes_B

Re: Natbib doesn't print @misc and et al.
24/11/2015 17:10, Johannes_B

Re: table numbering wrong in pdf
24/11/2015 13:29, KumarDinesh

Natbib doesn't print @misc and et al.
24/11/2015 04:20, BlazeAxtrius

Re: Font Color: Black
23/11/2015 11:43, Johannes_B

Re: Fatal error occurred, no output PDF file produced!
23/11/2015 11:36, Stefan_K

Re: Fatal error occurred, no output PDF file produced!
23/11/2015 11:20, Johannes_B